It’s been too long since I touched bamboo…

It’s been a while.  No doubt.  And it’s been bothering me lately.

If you’ve been following the time stamps, this comes quite a bit after I finished my 7622 Sir D.  Here is the Summer 2014 update on that:
– I needed to grind down the handle even more than I had to make it suitably small.  It’s tiny, but fittingly so.
– I liked it well enough with a GPX DT2F, but a lighter WF2 was a bit better.  The tip is REALLY soft and folds under itself easily. We found this out in July when I had it up to Vermilion for Dad’s first review.  But later, in August, I had it to a bluegill/ bass pond  and had a blast sightfishing with soft hackles to ‘gills… with a 1 weight line.  It works a lot better.  It’s really a 1 weight!  Yikes!
– I showed it off at the local “Bamboo Gathering” in September, held every year in Martell, WI.  A bunch of folks were pleased and surprised by it, because it’s fantastically light yet feels like it will fish well.
– And fish well it does…

I took it, along with my dad, to my favorite brookie stream in Wisconsin.  Initially we tried tossing dries after seeing a couple rises but after an hour with no activity whatsoever, I did my usual – knotted and threw a small Clouser on 4X tippet.  Not 3 strips in and an 8″ brookie came flying out of the glass-smooth water right about where my fly ought to have been. That was the beginning.

Dad switched over and we were jumping, rolling, and fighting 8-11″ browns and brookies like they were on their last night eating.  Every turn, cut, hole, and pocket held at least a fish or two.  Most of the bigger holes held well over a dozen willing takers.  Cool water made most of them leapers.

The evening began to set in and the water turned dark, the shadows became long.  We’d worked our way well upstream and were facing a long, gradually deepening hole that formed in a tight bend that ultimately faced to my left as it turned upriver.  The brookies were still enthusiastic, and it was still fun – hours later – having to actually whip the little fish in order to bring them to hand.  But as evening so often does, the big boys came out to play.  I set in to one heavier-than-usual take and nothing moved for a moment, then the largest brookie I’d taken in years showed itself and proceeded to give me concerns about putting a set in my new little rod.  When it finally came to hand, it was a full foot long and thick enough that I could barely get a hand under it for a viewing.  It was in full spawning colors deserving of a column in a magazine.  The day was made.

Last cast.  Call it, kid, or else you leave things hanging.

The loop uncurled.  Plip, stripstripstrip… That was when the water opened and my streamer disappeared in the jaws of a giant butter-yellow small-water brown… it clamped down and turned in mere inches of water…

******************************************************

That was really the last I touched bamboo.  I’ve been refinishing a Shakespeare steelhead-sized rod and putting intermediate wraps on it, a better reel seat and fighting butt, etc but not a lot of progress was made last fall.  Too much going on, not enough time, not enough motivation.  Til recently when I realized it has been over a year since I touched ‘boo with any real determination.  (Doesn’t help that my SPLTCN plates are no more – darn you Indiana…)

Dad bought himself a Payne – maybe it’s a 102 – and let me wiggle it over the holidays just a couple days ago.  Yep, that long stick of Arundinaria amabilis is still an old friend.  I’ve missed you.  It felt right with an old reel and somehow I suddenly caught the slightest whiff of drying varnish and toasted cane.  Yep, I’ve missed you ‘boo. We’ll have to get reacquainted before long.

Finally Finish-ed

June was a fun, busy month for me. And my rod, I suppose.

 

Well, it’s finished. Finally. I applied finish (lightly thinned Varmor R10) in a few coats and I learned a few things along the way:

1)      I used a bristle chip brush to apply the first coat. It didn’t go too badly, actually, but I didn’t have great control. Probably won’t be doing that again.

2)      I used a soft, low-lint rag to apply the second coat. NEVER DOING THAT AGAIN. The tips turned out okay, interestingly enough, but the butt? Ugh. I ended up sanding most of the finish off entirely.

3)      Three days is not enough time, even at 90 degrees F, for a varnish coat to dry. This is why I applied the first coat in early June but didn’t get through the last coat over the butt until about a week ago.

4)      Similarly, applying finish either a) highly thinned down OR b) at normal viscosity, and rotated (horizontally) for the first hour, is a great way to avoid drips. Brushing at normal out-of-the-can viscosity and hanging immediately = drips. Hence sanding.

5)      You cannot “touch up” a varnish coat. Hence sanding.

6)      I am the son of a woodworker, and if you haven’t picked it up yet, holy smokes am I picky about my varnish finish.

7)      My one-piece burl cork handle is kinda cool, but I probably won’t go with that look again. Just something about it that isn’t sitting quite right with me. I like it, but… Next time will be rings of one sort or another.

8)      For the time being, the “turkey baster” method worked well. I used a 5mL pipet for my “baster” but I did the entire butt using maybe 3mL of thinned finish. The final look came out pretty good actually, and was very conservative on using material. Note, I liked that. James Reid “CaneCaster” gave me a few tips on the method, which can be summed up as “thin heavily, up to 50% with good turps – drip lightly, rotating the rod as you go, and gently chase the bead – properly thinned you can not get drips (found this to be true) – no more than 1 coat per day”

 

Pics coming shortly, most likely to Facebook. I recently picked up a DSLR largely for this purpose so they should be good.

Wrapping the Stripper and First Few Snakes (plus extra tips!)

A couple weeks ago now I started wrapping the guides.  But let me back up first.

 

In following that my rod is a Wayne Cattanach taper (Sir D 7622), I found it appropriate to defer to him for guide spacing.  However, since the tip IS rather fine, I felt it best to support it with a couple extra guides.  Wayne’s formula (per his book) is simply to add 9/16” to each successive distance, so I started in close at 3” and went from there. 

 

With this spacing, I taped guides on and lined ‘er up with a GPX DT2.  Holy smokes is she sweet.  Almost overlined with that heavier line.  I think long-term I’ll want a Sylk or XPS on it.  Maybe even a good 1 weight, which isn’t entirely out of the question!

 

Anyway, this gave me a LOT of guides and actually too few  on the butt, so I opted for Tom Morgan’s 8’ 3wt spacing packed in to the same spacing as a 7’6” 3wt.  Now I have 3 guides on the butt section with the stripper 24” from the butt end.  It looks a little close but actually works out really well.  So I went with it, and using this new spacing I started wrapping.  I figure wrapping and gluing the stripper in place would fix my choice in spacing beyond any further questioning.

 

Thoughts and observations on wrapping: it’s not as hard as people make it out to be but it IS a major pain!    I opted for white wraps with a purple-wine colored accent wrap sandwiched over the middle of the guide foot, with white wraps on either side of it.  4 wraps of accent color, 8mm total wrap length.  I’ve always had a thing for invisible wraps so of course I wanted to do that one my own rod.

 

The wrapping went fine.  Trimming tag ends, however, presented a challenge due to the light tension on the thread (to help prevent shimmering in the white).  I did try burning the ends down with a lighter as per how it has always been done with nylon thread, but it resulted in marring the thread (gave it a gray cast) and I did put a very slight burn mark on my rod blank.  Not much, it looks like a pale olive-gray watermark in the cane by one of the stripper feet.  Oops.  Won’t be doing that again. I re-wrapped it, using a fresh razor to trip the thread tags after the wraps were otherwise finished (leaving the tags lets me keep tension on the wraps when moving them around right up til the glue-up point).

 

I added the FC Lite in perfect 1:1 with some acetone added to thin it out, maybe making it 1:1:0.6 or 0.7 parts acetone.  It wasn’t terribly thin but still flowed really well.  However, not quite well enough.  I had a little trouble with fine bubbles getting trapped in the thread though no issue with bubbles along the guide feet. 

Important side note: I do think pre-wetting the thread with denatured alcohol or acetone would help alleviate wetting issues with the thicker epoxy.  As of today I have another guide wrapped (closest to ferrule on the butt) and aim to finish most of it this weekend – I’ll play with a couple of these ideas and see how they work out. 

 

Anyway, about those extra tips…

 

Jerry had said he was going to make me an extra tip, however I found out later he was making me a FOURTH tip as well!  Lloyd delivered them to me up north here in my new locale on his way to Michigan a couple weeks ago, I had 3 male slides and 2 complete tips in the package.  Now I might just make a FIFTH tip, but I asked about getting another female ferrule for a new butt.  I want to shave down the butt section of the 7622 and make it more parabolic, possibly making it a good 1 weight or really light 2.  A true brookie rod.  This also means I will have a bunch of guides to order in again… but at least I have my guide spacing figured out!

Day 9 (12-7-13): Polishing, Ferruling – Attachment/ Notes on Lapping, Final Cut to Length (including Eyelets and Insert), Winding Check, Bluing

The first thing I was assigned in my last trip building was polishing the blank – 600 grit paper was used to put a nice shine on the rod and finalize the glue removal. 

Ferrule attachment included lapping the blank with sandpaper (220) to get a tight fit on the ferrule.  We lapped the blank using Jerry’s lathe (Sherline 4400) and a self-centering chuck – it’s strange how strong the cane blanks are, but we were careful not to overtighten the jaws.  The RPMs were controlled to about 120-150rpm, and starting at the end of the blank, we worked it down, little by little, checking the fit frequently.  The fit was best described as “comfortably snug” – the ferrule slid on easily but with moderate resistance.  Care was taken not to round the corners of the blank outside the ferrule tabs. 

Prior to gluing them on, Jerry scratched a single small channel on one of the flats to let the air out.  A small but crucial step. 

We glued the ferrules on using 2-ton epoxy, which had about a 20 minute cure time.  Swirl some inside the ferrule covering all the walls, dab a little on the butt end of the cane, and push it in until it seats.  The air pocket will provide some resistance, but pushing the cane firmly against something solid (a workbench, or wall) will squeeze the air bubble out.  It might take a second or few, but it will come.  Wipe the excess off, use a solvent-soaked Q tip to get rid of the rest, then using some heavy thread (we used 10lb backing) wrap the ferrule tabs down.  Stand the section ferrule-down until it cures. 

We didn’t lap the males down while I was there.  I was told to use 1000-1200 grit wet/dry paper for it.  I picked up some 1500 grit to be on the safe side since lapping is critical.  Little by little is the best way to go.  If you feel the need to hurry, put it down and come back later.

Once the ferrules were on, we did the final cut to length.  Using the marks previously made to denote the “proper” ends, we measured the depth of the tiptops and set the tip of the tube as the tip of the rod; a slight correction was made in the length of the cane to compensate for it.  Similarly the depth of the reel seat was determined and a fraction of an inch was removed from the butt of the blank to allow for the added length from the seat.  All 3 sections were exactly 45 inches long when we were done. 

Then we made a winding check and blued everything.  Bluing was easy, it was swabbing or dipping the bluing solution (caution: toxic) on the ferrules until the appropriate color was reached.  The ferrules had to be CLEAN or the solution would show where it wasn’t reaching the nickel silver substrate.  Touching up was easy with 4/0 steel wool.  I would imagine 320 grit paper would be okay too, so long as you’re gentle and don’t scratch it too badly.

I’d write down how we made the winding check but I think that’s a private matter.  Sorry!  The maker has his secrets, I won’t disclose them.

And that was it. This concludes my adventure in building a blank.  In leaving Saturday night, I was hit with a profound sadness and sense of loss that it was all over.  While driving to Cincinnati was always something I looked forward to, I realized just how much I really enjoyed my building experience.  I have GOT to put together another cane blank – it feels like this has become a part of me.

Days 7 (11-30) and 8 (12-1): Final Planing, Gluing, and Sanding – Part 2

As mentioned before, his resin is Epon 828 and hardened with Epikure 3140, which he uses normally in 1:1, but can go up to 2 parts epoxy to 1 part hardener (which is pretty close to 1:1 stoichiometry, or 100g to 198.4g epoxy).  So, first measure out the hardener for how much you think you’ll need, then get to that amount or just over with the epoxy; it’ll be dialed right in simply by your process so you won’t have anything to worry about.  That’s a convenient trick.  There are other epoxy systems that work well too – I’m exploring those right now (hint: DER 671-X75 or -T75).

 His batches were about 200-250 GRAINS total, but I only got through my butt and 1 tip with that before my cup was about dry.  Because that was too little, and my scale is a gram scale (not grains), I’m going to show you the math for converting:

Per Google, 1 gram = 15.432584 grains.  So Jerry’s batch size would have been about 15-16 grams.  THAT WAS TOO LITTLE.  Bear in mind I needed to make 2 batches to get through my rod, I used about 20-25 grams of glue, and I thought I was going rather sparingly with the glue despite being sure to obviously coat everything well.  In short, my rod wasn’t dripping – really thin coats are hard with that stuff at it’s full viscosity. Doing a rod any bigger and I would have wanted to have a 40-50g batch for myself.

 Mixing: this epoxy system (828 and 3140) turns a light, milky caramel color when mixed.  You have to be careful to get all the stuff off the sides and bottom since you can’t really see what you missed.  I also noticed it tacked up quite a bit in the 10 minutes or so following mixing and application.  I really thought a few drops of some solvent – acetone, denatured alcohol, etc – would have been nice to cut the viscosity, but then you would have to air dry the rod a bit to let the solvent flash off, then bake it lightly after binding to drive the solvent out of the rod.  Otherwise the potential for the solvent to affect your finish is there.  (I don’t think it would have much effect, if anything visible, but still – potential is there).

 ((PS – if you want to extend the shelf life of your adhesive materials to nearly infinitely long, keep them sealed and in the freezer.))

 Glue was applied with a cheap toothbrush.  The most “critical” sides to get were the two outside faces, because the natural tendency is to focus on the center strips, which leaves the junction of the two outside faces weaker due to having less glue.  Be sure to wet them well – the reflection in the light will be a good reference for your glue coverage.  The faster you can mix up your glue the faster it can be applied to the rod before it tacks up.  Frankly I would have preferred something like a 1″ white china “chip” brush or even a real bristle brush for better pickup and spreading (read: not so many dips in the cup for more to spread) and either way, white china brushes will allow themselves to be cleaned with acetone, mineral spirits, or some other thinner allowing them to be reused at least a couple times.  Preserving a nice WC brush will take a little work cleaning though.  Chip brushes can be tossed out if desired.

 If you haven’t been wearing them already, put on some cheap latex or nitrile gloves for this.  Pick up the section from the paper (it will be stuck by the adhesive’s tackiness) by the butt, gently teasing it up an inch or so. Then guide your fingers from the other hand slowly along to lift the entire piece bit by bit, eventually lifting the entire section up.  Now you have to prep it for the binder: once up, hold on to the butt and let it hang freely – that was very important and is how the sections should always be held while the glue is still uncured.  Guide the outside edges back together, taking care to make sure again that all of the enamel sides are facing outwards.  Squeeze (don’t slide your fingers!!) the section together; the glue’s tackiness will hold it nicely.  Work your way down the section and press the strips together all the way down.  Support the section (no bends if possible, minimal otherwise) and move it to the binder.  Then run it through the binder and move on to another section.  Don’t press the strips together and then set the section down before running it through the binder; sliding can occur.  That’s bad.

 After binding was done, a loop of binding thread was attached to the tip end of the section.  Then the section was grasped at both ends (or as near as reasonable) and pulled, almost stretched, to prevent sagging and bending. Then it was hung up to let the glue set up enough to allow sanding. It is important to note that the section was NEVER BENT, not even by gravity. We did sight down the section by supporting it in the middle, though, to check straightness.  It was most important not to let it sag as the tip and butt were held (especially on the tip sections).  If straightening needed to happen, we rolled the blank under a board to nudge it in the right direction.  Final straightening will happen after the glue cures, if it is still needed.

 Sanding occurred within 24 hours before the glue set up too much.  It was of a “hard rubber” consistency when taken off with 220 grit sandpaper.  Cooler temperatures will draw out the time before sanding is safe, and warmer temps will shorten it due to the different times in which the adhesive will set up.  Correct pressure for sanding is about the weight of the sanding block, or about 8 ounces.  Doing the tips gently also meant decreasing the pressure a bit to avoid rolling the tip as the third, fourth, and fifth flats were done (explained below).  The block must also be kept flat as in planing to maintain the apexes, otherwise they’ll round off and the hex shape will be greatly decreased.  This is also why soft-bottom blocks are a bad idea – a very flat, hard surface needs to be behind the paper to keep it flat.  Change paper frequently to avoid having to work at it too hard and risking injury (tendonitis is a big danger here) – one strip of 220 did about 2 flats on the butt and 3 flats on the tips.  By the time sanding has become work, the paper is dead.

It was suggested, and also found, that doing the tips of each section first was beneficial in keeping the hex shape.  This was, of course, most obvious on the tip of the tip section.  Moving down the blank toward the butt about 10 inches (more or less, depending on your particular taper) to find each flat where it was first well-defined, place the butt of your hand to hold the rod and keep it from rolling.  Start sanding with light strokes in the direction of the rod tip ONLY to slowly remove the glue and reveal the flat.  Work your way down until the tape, glue, and pencil marks are gone.  Then flip the rod 180 degrees and do the opposite flat.  I found it easiest to then do a third flat by moving another 4 or 5 inches down the rod and repeating the process of cleaning up the tip.  Moving further down the blank allowed better stability. It’s not necessary but I found it convenient with my little rod.  Work the tip gently to avoid twisting it.  The problem with the tip is that its small diameter doesn’t correct for the excess glue forming concave drips on the outside of the rod blank, so it leads to a round rod.  Be very careful not to round out the tip.  Remember to be sanding in only one direction – the paper tends to grab the tacky adhesive and you don’t want to rip the rip back that sharply.  It will either put a nasty set in right at the tip, or break.  Not worth the few extra minutes it takes doing it right.  This isn’t an issue with mid-sections nearly as much or with butt sections at all due to the extra rigidity of all the wood in the blank at that point.

Once the tip is done and the rod is sanded back at least 10-15 inches from the tip (finer rods need to be sanded further back), begin really sanding the glue off by doing 6-8″ sections at a time, sanding back and forth using the full weight of the block.  It goes surprisingly fast – don’t push down on the block despite the temptation to go even faster.  It’s not worth it, and it’s not needed.  It is very exciting to see the rod this close to being finished but relax, take it easy, the best is yet to come – ferruling and finishing.

Hang it back up (clamps are fine now that everything has been sanded off; string doesn’t have anything to stick to anymore) and let it cure for a week.

 

Days 7 (11-30) and 8 (12-1): Final Planing, Gluing, and Sanding – Part 1

My lovely wife Kristin decided to come with me for the final planing since I’d told her it would be a short day, a few hours at most, and would give Jerry someone new to talk to.  It would also let her see what a good rod shop looked like – a secret motive, heh heh heh.

Final planing was rather straightforward, it involved setting the planing form to its final dimension, resharpening all the blades, adjusting any angles, and letting yourself get a fresh mindset for a new day.  The break also allowed a chance to warm up the glues if the epoxy resin had crystallized. 

This time, however, only .001″ or less came off with each pass of the plane.  When it got close, the last few passes were made with only the gentlest of pressures – I used my fingers to push the plane along little by little as only wisps of cane were coming off.  Each side was done that way.  It went fairly quickly despite the small cuts.  Jerry had done the butt and first tip for me to save some time, but it really wasn’t necessary – it all went easily enough that a couple hours would have been more than enough time to get the final planing done.  But then the fun came: glue-up.

In getting ready to glue up the rod, before I ever touched the blank today, I was told that attention to detail would be the greatest yet, and that all the gremlins seem to come out in the glue-up, because if today goes bad, all the detail and hard work from days previous go out the door. 

Glue-up prep: We laid out thin strips of masking tape (1/4″ wide) about a foot apart on a long, flat surface free of dust.  Mandatory strips are 1″ from the tip and butt of the section. My 45″ sections had 5 strips of tape on them.  Jerry uses a piece of slate about 5×1 for all this.  A glossy varnished board would do the trick too. Bind the strips of 1/4″ with some wider masking tape (we used a 1 inch long strip of 3/4″).  Lay your FIRST strip down, #1. You should have labeled your strips the whole time prior to help with node placement; you’ll use these numbers again now.  (This is where it gets detailed and kinda tricky.) Since you should have a witness mark on the outside (enamel side) of the cane from planing yet, make a small mark on the planed surface of the strip at the same point – so you can see it when it’s laying on the board, since the enamel side of the strip will be face down.  Make this same mark on all the strips at the same point.  Lay the strips down in successive order, pressing them down on the tape.  Don’t worry if the ends or tips are slightly off.  It doesn’t really matter. That’s what the witness marks are for – to keep everything at the same point, somewhere. The few inches of excess at each end are going to be cut off.

Butt strips should be placed about a millimeter apart on the tape.  If there is a midsection, place them a little closer but not quite touching.  Tip strips can barely touch.

When they are all taped down and ordered, cut the tape with a single-edged razor flush on the side nearest you, with maybe a 2mm tag allowed on the other (far) side.  Do this for all the strips of tape.  And don’t nick the cane or it’ll be an instant glue line.  You also don’t want tags on both sides for reasons that will come apparent later.

At this point you have the strips with the enamel side all bound to short sections of tape.  Pick up each section and hold it by the butt end, letting it hang in your hand.  Take the outside faces (the 2 planed faces of strips that were not facing another strip) and place them together.  It might take a little fanaggling but they should come together.  Verify all the enamel sides are facing out – easy to do since they are labeled on the butt ends, so they all have writing (planed sides don’t have writing on them at this point).  The strips should have formed a nice hex shape.  If the strips are a little loose, peel back the tape and squeeze the bundle together, then lay down the tape again to tighten them up a bit – this is the reason for having 1 tag of tape to pull on; 2 tags would have adhered together and been a bear to separate.  Work your way down the blank to tighten and secure the tape all the way down the section.  Repeat for each mid and tip section.

With each section tape-bound, find the junction of strips 1 and 6, and then gently run a razor up to slice the tape.  Again: be careful not to nick the cane, or it will be an instant glue line.  Slice the tape on each section to expose the pith-side of the strips all the way up.  Be exceptionally careful doing the tips….

Lay the sections down on your gluing surface (we just paid newspaper down on the same board we taped up on). Take a small, soft brush (a good paintbrush or toothbrush are both good choices) and dust off the strips, butt-end working to tips of each section, to remove any dust or loose fibers.  Your sections are now ready for glue.

Day 6 (11-23-13): Finish Initial Planing – Entirely

Today was an 8 hour day of finishing all the initial planing that I had left, 8 strips for the tips.  I found it smart to take a break after 3 hours or so again, breaking for lunch after doing 4 of the strips.

I timed myself on a few strips – one I did in 22 minutes, another in 25, the last in 24. It’s very possible to get stuff done without wasting time “being careful” while still being careful.

I messed around with a plane a bit since one strip took nearly an hour to get through; I was only getting about .001” at a time.  Normally initial planing is done best at 2-3 thousandths.  My initial adjustment was .00 4-5” which was taking a heavy bite and way too much for the tips – a heavy bite, open mouth (on the plane), and/or dull blade will bite too far in to the cane and take chunks of fibers with it, leading to low dimensions, gaps, and large, open curls.  I never got large curls thanks to the small mouth, but it was risky, and I got lucky.

The tips are especially susceptible to overly-aggressive planing because the light dimension can be lifted out of the form when the plane bites too deeply.  Butts aren’t as much an issue because they’re more rigid due to the extra thickness, but tips… eh…

If the blade is not level to the bottom of the plane, the backside of it can be tapped on the same side that’s too deep – it will help correct the angle.  Good angles = good strips.

Post add: My wrist was sore after all this planing.  Not so much in the muscle of my forearm (which was a little knotted up but was massaged out easily and quickly) but rather the tendon sheath on the back of my wrist, right between the two bumps of forearm bone.  It felt very tender to the touch, like it was bruised.  A somewhat sharp, annoying pain when I touched it.  I could feel the inflammation – it felt somewhat like a muscle knot but the pain signal was different.  It took until now, morning of 11-26-13, for it to feel mostly normal.  Still slightly noticeable to the touch, but there is barely any tenderness remaining.  Whew, note to self, don’t plane for more than 2-3 hours, tops.  Repetitive stress injuries are NOT worth the risk.  There was a recent thread on the Classic Fly Rod forum about injuries – it seems that shoulder/ cuff injuries, as well as “tennis elbow” and carpal tunnel are common builder injuries.  Knowing my dad’s history with this, I don’t want to risk going down that road.  Getting a week’s work done in a day is not worth being in pain when I no longer heal as fast as I do at 25 or 30 anymore.

Day 5 (11-9-13): Start Tips

Nothing special, just a lot more planing.  Jerry set up the planing form with the initial tip settings on 0.010” over the final dimension. It was fun, again, and I did a lot in the 6 hours or so I was there.  I noticed though that I can only plane for so long before my wrist and forearm are stressed.  I have to be careful – much over 3 or 4 hours and I really have to watch my form carefully.  Music would be nice to have…

Midweek (11-5/6-13): I caught myself thinking…

…about having my own rod company.  At this stage nothing would be for sale, and after coming up with this idea I teased Dad the next morning a bit, saying that my waiting list was awesome, approximately 3-5 years at this point! But I do want to put a brand on my rods, and with a bit of thought on what mattered to me and what I liked of current manufacturers (Sweetgrass, Sweetwater, Otter Creek (Jerry’s name), among others) along with a crafty but neat way of hiding the derivation, I came up with Plumbrook.  Plumbrook Rods.  It seems fitting, especially considering that I seem to have this thing for putting a deep purple on my rod – dark purple trim wraps, accents, and a purpleheart seat insert are only appropriate.

Day 4 (11-3-13): Finish Initial Plane of Butt Strips

((I ran off to Minneapolis from 10-18 through 10-27 getting married, hence the delay.))

I took care of the butt strips for the initial planing.  Jerry and I looked around online at a bit, talked a bit, and kinda shot the breeze for a while so I only got the 4 remaining butt strips done.  Initially, anyway.  The form was still very much in alignment with where it needed to be so adjustments were very minimal, which made planing easy.  Jerry had sharpened the blades for me prior to my arrival.